|
Scope of application:Wind generator, large motor baking, composite materials
drying oven/industrial oven/industrial oven manufacture/high capacity oven
Industrial oven has a wide range of USES: suitable for baking chemical gas and food processing industry to bake goods, substrate stress removal, ink curing, paint film drying, etc. Widely used in electronics, electrical, communications, electroplating, plastic, metal chemical, food, printing, pharmaceutical, PC board, powder, immersion, spraying, glass, ceramics, wood building materials...... And so on the precision baking, drying, tempering, preheating, shaping, processing and so on.
Structure of industrial oven
The industrial oven is an
internal and external double-layer structure, the shell is an angle steel thin
steel plate, and a fiber material is filled between the inner and outer
double-layer shells. The fiber material used in the industrial oven is mainly aluminum
silicate, and can play the role of heat preservation and form a reliable
heat-insulating layer. The industrial oven is equipped with a hot air
circulation system and a temperature measurement and control system.
principle of operation
The temperature is controlled
by the connection between the digital display instrument and the temperature
sensor. The hot air circulation system is divided into horizontal type and
vertical type by using the hot air circulation air supply mode. After accurate
calculation, the air source is driven by the air supply motor to send the hot
air to the air duct and enter the oven studio through the electric heater, and
the air suction duct after use can be used as the air source to reheat, so that
the temperature uniformity can be effectively improved. If the box door is
switched on and off in use, the air supply circulation system can quickly
restore the operating state temperature value.
The principle of an industrial
oven
When the industrial oven is
working, the operator obtains the temperature value inside the industrial oven
through the instrument and the temperature sensor, and operates through the
control system. Compared with the ordinary heat dissipation heating method, the
hot air circulation heating mode of the industrial oven has better gas flow and
can speed up the drying speed of the materials in the industrial oven.
The hot air circulation system
of industrial oven is composed of air supply motor, air turbine and electric
heater. The air supply motor drives the air turbine to send out cold air. The
cold air is heated by electric heating equipment and carries heat energy, and
then enters the oven studio through the air duct.
The hot air circulation system
of industrial oven is beneficial to improve the uniformity of air temperature.
in the process of transporting materials at the door of industrial oven switch
box, the temperature value will be affected, and the uniformity of hot air
circulation system will be beneficial to restore the temperature value of working
state within the maximum speed.
Daily maintenance
1.Clean the surface and inner
cavity dust and keep the machine clean and hygienic.
2. Check whether the ammeter current is the
same as normal, if anything, notify the repairman to repair.
3. When there is a sudden power
outage, turn off the heating switch to prevent automatic start on incoming
calls.
4. Check that the fan is
running properly and if there is any abnormal sound, if there is an immediate
shutdown of the machine and notify the repairman to overhaul.
Monthly maintenance
1.Check the vents for blockage
and clean up the dust.
2. Whether the fan is running properly and
whether it is reversed or not.
3. The repairman checks whether
the current is normal.
4. Check that the temperature
controller is accurate. If it is not accurate, please adjust the static
compensation or sensor correction value of the temperature controller.
5. Check the heating pipe for damage and aging
of the line.
6. Check whether the delay
device is accurate and whether the error is allowed.
Characteristics of the equipment
1、Design according to the proportion of human engineering, easy operation, modern appearance.
2、Argon Arc full Welding of all stainless Steel in Inner to prevent dust from the machine itself.
3、Unique air-duct design to ensure the temperature inside is uniformity
4、First-class technology of heat &thermal insulation, sealing effect is excellent.
5、Double over-temperature protection, safer and more reliable.
6、Rising up fast, and the temperature is stable and accurate.
7、The shell temperature is low, which has little effect on the indoor environment temperature.
8、According to the product set up a variety of heating and air mode, energy saving, safety and environmental protection.
9、Module design:Each section manipulation and operation in flexible independently can be available.
10、Colors can be customized base on color card.
Technical Parameters of Industrial Oven | |||||
Type | Common | Clean | Finishing Cure | Explosion-Proof | Vacuum |
Temperature range | 0-250℃ | 0-350℃ | 0-550℃ | 0-700℃ | 700℃ |
Temperature Homogeneity | ±1℃ | ±3℃ | ±5℃ | ±1.5%℃ | |
Heating Rate | ≦5℃/min | ≦8℃/min | ≦10℃/min | 10℃/min | |
Energy Type | electrical | Gas | Steam | Air Energy | Other |
Heating Mode | Electric | Infrared | Other | ||
Chamber | Single | Twin | Three | Other | |
Sheathing Material | Cold Drawing Spray-Paint |
Stainless S teel |
Other | ||
Chamber Material |
Stainless S teel 201 |
Stainless S teel 304 |
Galvanized Sheet | Other | |
Heat Insulating Material | Aluminosilicate Rock Wool | Insulating Fibre-Board | Firebrick | Other | |
Air Transport Mode | Left and Right | Up and Down | Front and Behind | Symmetrical Left and Right | |
Air Motor Position | Top | bottom | Hindside | Sidepiece | Other |
Number of Explosion-proof Doors | One | Two | Other | ||
Manual door | Single Door | Double Door | Three Doors | Other | |
Automatic Door | Revolution door | Side Sliding Door | Lift door | Roll-Up Door | Other |
Cart Type | Double-Deck Cart | Motor-Trolley | Landing Cart | Automatic Trolley | Other |
Power Control | SSR | SCR | Other | ||
Control Mode | Instrument Control | HMI Control | Network Control | Other | |
Timing Mode | Manual | Automatic | Other | ||
Safety Protection Function | Overtemperature | Overload | Phase Sequence | Earth Leakage Protection | Other |
Detection Function | Temperature | Thickness | Flame | Pressure | Other |
Main parameters can be customized according to customer requirements:
Liner size | W2000*L2500*H2000 | |||||||||
Dimensions | W2540*L2640*H2540 | |||||||||
Tem range | RT-300℃ | |||||||||
Temperature fluctuation | ±1°C | |||||||||
Temperature uniformity | ±3°C | |||||||||
Heating rate | ≤8°C/min | |||||||||
Circle style of wind | Horizontal symmetrical circulation | |||||||||
Power supply | 380V 50Hz | |||||||||
Total Power | 75KW |
Device Configuration:
Construction | Standard Configuration | Optional Configuration | Description | |
Shell material | 2mm Thick rock wool board | Stainless steel or exotic material | ||
Surface treatment | Electrostatic spray | Color in optional | ||
Material of liner | Thickness in 1.5mm 304Stainless steel | |||
Frame | Aluminium | Angle iron of stainless steel | ||
Thermal insulation material | Encrypted alumina silicate cotton | Glass Fiber | ||
Control system | Cooling systems | 1.5KW Motor temperature | Wind speed in adjustable | |
Heater | Electric heater | Optional: electricity, gas or liquid heating | ||
Thermostat | Touch screen、Space temperature control module | Programmed temperature control | Specify | |
overtemperature control | Space temperature indicator | Mechanical temperature control | Specify | |
multipoint recorder | No | No paper or paper recorder | Specify | |
Temperature sensor | Omron K thermocouple | |||
Control way | Human Machine Interface | Human Machine Interface or remote computer control | Specify | |
Function | Automatic thermostat | Yes | ||
Thermal protection | Yes | |||
Manual and automatic timing | Digital display timer | |||
sound-light alarm | Yes | |||
Ground detection | Yes | |||
Phase sequence | Yes | |||
overload protection | Yes | |||
concentration detection | No | (VOC) | Specify | |
Material temperature detection | No | infrared thermometer | Specify | |
Pressure inside the chamber | No | pressure gauge | Specify | |
Flame pressure test | No | Flame detector | Specify | |
Automatic control of air discharge | No | High temperature anemometer | Specify |
Graphic wind circulation:
![]() |
![]() |
![]() |
![]() |
Single-sided supply air type | Double-face type | Double-face blast with explosionproof | Thermal rising type |
![]() |
![]() |
![]() |
![]() |
Thermal rising type | Thermal radiation type | Hot air radiation | Hot air radiation |
Copyright@Ningbo Sibo.X Industrial Equipment Co., Ltd. Add:Changxin road No.618,Jiangbei district,Ningbo city.
Tel:+86-574-87081082 Mobile:+86-13586647115 Email:sibxsun@sibxcn.com Contact:Jane wan